Sony Operations - Darkgrade

SDIO_OpenSession (`0x9210`)

Open Session with Function Mode. Data Direction: none

Operation Parameters

Parameter	Required	Description
SessionId	✓	Unique session identifier
FunctionMode	✓	Function mode

FunctionMode values:

Value	Name	Description
`0x0`	REMOTE	Remote Control Mode
`0x1`	CONTENT_TRANSFER	Content Transfer Mode
`0x2`	REMOTE_AND_CONTENT_TRANSFER	Remote Control with Transfer Mode

Response Parameters

None

SDIO_Connect (`0x9201`)

This is for the Sony SDIO authentication handshake. Data Direction: out Codec Type: Custom Codec

Operation Parameters

Parameter	Required	Description
phaseType	✓	Connection phase (1, 2, or 3)
keyCode1	✓	KeyCode1 (always 0x00000000)
keyCode2	✓	KeyCode2 (always 0x00000000)

phaseType values:

Value	Name	Description
`0x1`	PHASE_1	Authentication Phase 1
`0x2`	PHASE_2	Authentication Phase 2
`0x3`	PHASE_3	Authentication Phase 3

keyCode1 values:

Value	Name	Description
`0x0`	DEFAULT	Default key code

keyCode2 values:

Value	Name	Description
`0x0`	DEFAULT	Default key code

Response Parameters

None

SDIO_GetExtDeviceInfo (`0x9202`)

Get the protocol version and the supported properties of the connected device. Data Direction: out

Operation Parameters

Parameter	Required	Description
initiatorVersion	✓	Initiator Protocol Version
flagOfDevicePropertyOption	✓	Enables extended SDIO Device Property / SDIControlCode

initiatorVersion values:

Value	Name	Description
`0x12c`	3.00	Protocol Version 3.00

flagOfDevicePropertyOption values:

Value	Name	Description
`0x0`	DISABLE	DISABLE
`0x1`	ENABLE	ENABLE

Response Parameters

None

SDIO_GetExtDevicePropValue (`0x9251`)

Get the DevicePropInfo. Data Direction: out Codec Type: Custom Codec

Operation Parameters

Parameter	Required	Description
DevicePropCode	✓	Property code to get

Response Parameters

None

SDIO_SetExtDevicePropValue (`0x9205`)

Set a DevicePropValue for a device property. Data Direction: in

Operation Parameters

Parameter	Required	Description
DevicePropCode	✓	Property code to set
flagOfDevicePropertyOption	✓	Enables extended SDIO Device Property / SDIControlCode

flagOfDevicePropertyOption values:

Value	Name	Description
`0x0`	DISABLE	DISABLE
`0x1`	ENABLE	ENABLE

Response Parameters

None

SDIO_ControlDevice (`0x9207`)

Set the SDIControl value for the SDIControlCode. Data Direction: in

Operation Parameters

Parameter	Required	Description
sdiControlCode	✓	Control property code
flagOfDevicePropertyOption	✓	Enables extended SDIO Device Property / SDIControlCode

flagOfDevicePropertyOption values:

Value	Name	Description
`0x0`	DISABLE	DISABLE
`0x1`	ENABLE	ENABLE

Response Parameters

None

SDIO_GetAllExtDevicePropInfo (`0x9209`)

Obtain all support DevicePropDescs at one time. The host will send this operation at regular intervals to obtain the latest (current) camera settings. Data Direction: out

Operation Parameters

Parameter	Required	Description
flagOfGetOnlyDifferenceData	✓	Flag of get only difference data
flagOfDevicePropertyOption	✓	Enables extended SDIO Device Property / SDIControlCode

flagOfDevicePropertyOption values:

Value	Name	Description
`0x0`	DISABLE	DISABLE
`0x1`	ENABLE	ENABLE

Response Parameters

None

SDIO_GetOsdImage (`0x9238`)

Get OSD image Data Direction: out

Operation Parameters

None

Response Parameters

None

SDIO_GetPartialLargeObject (`0x9211`)

Get partial object from the device. Same as GetPartialObject on PIMA 15740 but with 64-bit offset support. Data Direction: out

Operation Parameters

Parameter	Required	Description
ObjectHandle	✓	Object handle
OffsetLower	✓	Offset in bytes (lower 32 bits)
OffsetUpper	✓	Offset in bytes (upper 32 bits)
MaxBytes	✓	Maximum number of bytes to obtain (does not support 0xFFFFFFFF)

Response Parameters

Parameter	Required	Description
ActualBytesSent	✓	Actual number of bytes sent

SDIO_SetContentsTransferMode (`0x9212`)

Enable content transfer mode to access memory card content. Data Direction: none

Operation Parameters

Parameter	Required	Description
ContentsSelectType	✓	The Initiator should send this command with one of the following values:
TransferMode	✓	The Initiator should send this command with one of the following values:
AdditionalInformation	✓	The Initiator should send this command with one of the following values:

ContentsSelectType values:

Value	Name	Description
`0x0`	INVALID	INVALID
`0x1`	CAMERA	Select on the Camera
`0x2`	HOST	Select on the Remote/Host Device

TransferMode values:

Value	Name	Description
`0x0`	DISABLE	DISABLE
`0x1`	ENABLE	ENABLE

AdditionalInformation values:

Value	Name	Description
`0x0`	NONE	NONE
`0x1`	CANCEL	CANCEL

Response Parameters

None

​SDIO_OpenSession (0x9210)

​Operation Parameters

​Response Parameters

​SDIO_Connect (0x9201)

​Operation Parameters

​Response Parameters

​SDIO_GetExtDeviceInfo (0x9202)

​Operation Parameters

​Response Parameters

​SDIO_GetExtDevicePropValue (0x9251)

​Operation Parameters

​Response Parameters

​SDIO_SetExtDevicePropValue (0x9205)

​Operation Parameters

​Response Parameters

​SDIO_ControlDevice (0x9207)

​Operation Parameters

​Response Parameters

​SDIO_GetAllExtDevicePropInfo (0x9209)

​Operation Parameters

​Response Parameters

​SDIO_GetOsdImage (0x9238)

​Operation Parameters

​Response Parameters

​SDIO_GetPartialLargeObject (0x9211)

​Operation Parameters

​Response Parameters

​SDIO_SetContentsTransferMode (0x9212)

​Operation Parameters

​Response Parameters

SDIO_OpenSession (`0x9210`)

Operation Parameters

Response Parameters

SDIO_Connect (`0x9201`)

Operation Parameters

Response Parameters

SDIO_GetExtDeviceInfo (`0x9202`)

Operation Parameters

Response Parameters

SDIO_GetExtDevicePropValue (`0x9251`)

Operation Parameters

Response Parameters

SDIO_SetExtDevicePropValue (`0x9205`)

Operation Parameters

Response Parameters

SDIO_ControlDevice (`0x9207`)

Operation Parameters

Response Parameters

SDIO_GetAllExtDevicePropInfo (`0x9209`)

Operation Parameters

Response Parameters

SDIO_GetOsdImage (`0x9238`)

Operation Parameters

Response Parameters

SDIO_GetPartialLargeObject (`0x9211`)

Operation Parameters

Response Parameters

SDIO_SetContentsTransferMode (`0x9212`)

Operation Parameters

Response Parameters